Verify Network

This section goes into depth on how SD-Core (which runs inside the Kubernetes cluster) connects to either physical gNBs or an emulated RAN (both running outside the Kubernetes cluster). For the purpose of this section, we assume you already have a scalable cluster running (as outlined in the previous section), SD-Core has been installed on that cluster, and you have a terminal window open on the Master node in that cluster.

Figure 50 shows a high-level schematic of Aether’s end-to-end User Plane connectivity, where we start by focusing on the basics: a single Aether node, a single physical gNB, and just the UPF container running inside SD-Core. The identifiers shown in gray in the figure (10.76.28.187, 10.76.28.113, ens18) are taken from our running example of an actual deployment (meaning your details will be different). All the other names and addresses are part of a standard Aether configuration.

Figure 50. The UPF pod running inside the server hosting Aether, with core and access bridging the two. Identifiers 10.76.28.187, 10.76.28.113, ens18 are specific to a particular deployment site.

As shown in the figure, there are two Macvlan bridges that connect the physical interface (ens18 in our example) with the UPF container. The access bridge connects the UPF downstream to the RAN (this corresponds to 3GPP’s N3 interface) and is assigned IP subnet 192.168.252.0/24. The core bridge connects the UPF upstream to the Internet (this corresponds to 3GPP’s N6 interface) and is assigned IP subnet 192.168.250.0/24. This means, for example, that the access interface inside the UPF (which is assigned address 192.168.252.3) is the destination IP address of GTP-encapsulated user plane packets from the gNB.

Following this basic schematic, it is possible to verify that the UPF is connected to the network by checking to see that the core and access are properly configured. This can be done using ip, and you should see results similar to the following:

$ ip addr show core
15: core@ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 06:f7:7c:65:31:fc brd ff:ff:ff:ff:ff:ff
    inet 192.168.250.1/24 brd 192.168.250.255 scope global core
       valid_lft forever preferred_lft forever
    inet6 fe80::4f7:7cff:fe65:31fc/64 scope link
       valid_lft forever preferred_lft forever

$ ip addr show access
14: access@ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 82:ef:d3:bb:d3:74 brd ff:ff:ff:ff:ff:ff
    inet 192.168.252.1/24 brd 192.168.252.255 scope global access
       valid_lft forever preferred_lft forever
    inet6 fe80::80ef:d3ff:febb:d374/64 scope link
       valid_lft forever preferred_lft forever

The above output from ip shows the two interfaces visible to the server, but running outside the container. kubectl can be used to see what’s running inside the UPF, where bessd is the name of the container image that implements the UPF, and access and core are the last two interfaces shown below:

$ kubectl -n omec exec -ti upf-0 bessd -- ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
3: eth0@if30: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1450 qdisc noqueue state UP group default
    link/ether 8a:e2:64:10:4e:be brd ff:ff:ff:ff:ff:ff link-netnsid 0
    inet 192.168.84.19/32 scope global eth0
    valid_lft forever preferred_lft forever
    inet6 fe80::88e2:64ff:fe10:4ebe/64 scope link
    valid_lft forever preferred_lft forever
4: access@if2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
    link/ether 82:b4:ea:00:50:3e brd ff:ff:ff:ff:ff:ff link-netnsid 0
    inet 192.168.252.3/24 brd 192.168.252.255 scope global access
    valid_lft forever preferred_lft forever
    inet6 fe80::80b4:eaff:fe00:503e/64 scope link
    valid_lft forever preferred_lft forever
5: core@if2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
    link/ether 4e:ac:69:31:a3:88 brd ff:ff:ff:ff:ff:ff link-netnsid 0
    inet 192.168.250.3/24 brd 192.168.250.255 scope global core
    valid_lft forever preferred_lft forever
    inet6 fe80::4cac:69ff:fe31:a388/64 scope link
    valid_lft forever preferred_lft forever

When packets flowing upstream from the gNB arrive on the server’s physical interface, they need to be forwarded over the access interface. This is done by having the following kernel route installed, which should be the case if your Aether installation was successful:

$ route -n | grep "Iface\|access"
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.252.0   0.0.0.0         255.255.255.0   U     0      0        0 access

Within the UPF, the correct behavior is to forward packets between the access and core interfaces. Upstream packets arriving on the access interface have their GTP headers removed and the raw IP packets are forwarded to the core interface. The routes inside the UPF’s bessd container will look something like this:

$ kubectl -n omec exec -ti upf-0 -c bessd -- ip route
default via 169.254.1.1 dev eth0
default via 192.168.250.1 dev core metric 110
10.76.28.0/24 via 192.168.252.1 dev access
10.76.28.113 via 169.254.1.1 dev eth0
169.254.1.1 dev eth0 scope link
192.168.250.0/24 dev core proto kernel scope link src 192.168.250.3
192.168.252.0/24 dev access proto kernel scope link src 192.168.252.3

The default route via 192.168.250.1 directs upstream packets to the Internet via the core interface, with a next hop of the core interface outside the UPF. These packets then undergo source NAT in the kernel and are sent to the IP destination in the packet. This means that the 172.250.0.0/16 addresses assigned to UEs are not visible beyond the Aether server. The return (downstream) packets undergo reverse NAT and now have a destination IP address of the UE. They are forwarded by the kernel to the core interface by these rules on the server:

$ route -n | grep "Iface\|core"
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
172.250.0.0     192.168.250.3   255.255.0.0     UG    0      0        0 core
192.168.250.0   0.0.0.0         255.255.255.0   U     0      0        0 core

The first rule above matches packets to the UEs on the 172.250.0.0/16 subnet. The next hop for these packets is the core IP address inside the UPF. The second rule says that next hop address is reachable on the core interface outside the UPF. As a result, the downstream packets arrive in the UPF where they are GTP-encapsulated with the IP address of the gNB.

Note that if you are not finding access and core interfaces outside the UPF, the following commands can be used to create these two interfaces manually (again using our running example for the physical ethernet interface):

$ ip link add core link ens18 type macvlan mode bridge 192.168.250.3
$ ip link add access link ens18 type macvlan mode bridge 192.168.252.3

Beyond this basic understanding, there are three other details of note. First, we have been focusing on the User Plane because Control Plane connectivity is much simpler: RAN elements (whether they are physical gNBs or gNBsim) reach the AMF using the server’s actual IP address (10.76.28.113 in our running example). Kubernetes is configured to forward SCTP packets arriving on port 38412 to the AMF container.

Second, the basic end-to-end schematic shown in Figure 50 assumes each gNB is assigned an address on the same L2 network as the Aether cluster (e.g., 10.76.28.0/24 in our example scenario). This works when the gNB is physical or when we want to run a single gNBsim traffic source, but once we scale up the gNBsim by co-locating multiple containers on a single server, we need to introduce another network so each container has a unique IP address (even though they are all hosted at the same IP address). This more complex configuration is depicted in Figure 51, where 172.20.0.0/16 is the IP subnet for the virtual network (also implemented by a Macvlan bridge, and named gnbaccess).

Figure 51. A server running multiple instances of gNBsim, connected to Aether.

For completeness, Figure 52 shows the Macvlan setup for the Quick Start configuration, where both the gnbaccess bridge and gNBsim container run in the same server as the Core (but with the container manged by Docker, independent of Kubernetes).

Figure 52. The Quick Start configuration with all components running in a single server.

Finally, all of the configurable parameters used throughout this section are defined in the core and gnbsim sections of the vars/main.yml file. Note that an empty value for core.ran_subnet implies the physical L2 network is used to connect RAN elements to the core, as is typically the case when connecting physical gNBs.

core:
    standalone: "true"
    data_iface: ens18
    values_file: "config/sdcore-5g-values.yaml"
    ran_subnet: "172.20.0.0/16"
    helm:
       chart_ref: aether/sd-core
       chart_version: 0.12.6
    upf:
       ip_prefix: "192.168.252.0/24"
    amf:
       ip: "10.76.28.113"

gnbsim:
    ...
    router:
        data_iface: ens18
        macvlan:
            iface: gnbaccess
            subnet_prefix: "172.20"